Setup the Reach RS2

A GNSS base station is necessary to produce an accurate result from the R2A or R360. Here's how to set up for optimal results:

1. Ensure No Electronics Nearby

Keep all electronics at least 6 feet (2 meters) away from the base.

Electronic devices may produce RF noise that could affect the reception of the GNSS signal.

2. Clear Sky View

The base station needs to have a clear sky view 30 degrees above the horizon. There should be no obstacles that could block the view like buildings, trees, cars, humans, laptops, etc.

base-placement good

The picture on the left demonstrates desirable conditions for the base location such as:

  • open field
  • top of the hill

The picture on the right  is an example of undesirable surrounding conditions such as

  • reduced view of the sky
  • possible obstructions, buildings
  • nearby vegetation
  • under trees
  • indoors 

3. Placing Reach RS2

Place the Reach RS2 on  the ground and make sure it's leveled as shown in the photo below.

  • If you are setting up base coordinates, place the Reach RS2 precisely above the marked point on the tripod and leveled.
  • Here's some images of what a known point may look like in the field: 
GCP

Measuring the base

  • Antenna height is measured as the distance between the mark and the antenna reference point (ARP).
  • For Reach RS2, consider the antenna height as the distance between the mark and the bottom of Reach RS2 (h in the figure above) plus 134 mm.

  • The distance between the Base and the Drone shouldn't exceed 10 km. A general rule of thumb is, you will lose 2 parts in accuracy per million. (e.g., at 10 km you will lose 2 cm of accuracy) Because of this we recommend to always have a base station located within 10 km of your project area.
  • If you collect your base station data over a known point, then you will be able to use that known point (converted to WGS 84) when entering your base station location into the ROCK Pre-processing Software.

4. Reach RS2: First Start

Watch the video below to update the RS2 firmware.

Check out Emlid Reach RS2 quick start guide

5. Turn on Reach

Press and hold the power button until all the LEDs light up. When the loading animation stops, Reach RS2 has booted up and is fully available.

6. Connect to Reach via Wi-Fi and open Emlid Flow

Make sure that Reach is broadcasting Wi-Fi: the LED must be solid white. Connect to RS2 like to a usual Wi-Fi network. By default login and password are these:

Login Password
reach:xx:xx emlidreach

Check the Wi-Fi LED. Solid blue network LED stands for successful connection to a Wi-Fi network. If it's solid white again, that means Reach switched back to hotspot mode. In this case check that you've entered the information for your Wi-Fi network correctly and try again.

Emlid Flow App

  • Download the app for iOS or Android. Get it from the App Store, Google Play or scan the QR code on the sticker on top of Reach..
  • Open Emlid Flow app. In Emlid Flow you'll see a list of Reach receivers in the same Wi-Fi network as your device. Tap the one you want to work with.

7. Setup the Reach RS2

Configure this once and always use these settings.

  • Connect to Reach RS2 and open RTK Settings tab.
  • Set Positioning mode to Static.
  • Pick each of the satellite systems.
  • Set the Update rate at 1 Second.
  • DO NOT CHECK "THIS  LOG IS FOR OPUS" BOX

IMG_0671-1

Enable Logging

  • Open the Logging tab.
  • Set Raw data to Rinex 3.03 and toggle on
    • RINEX is a industry standard for raw data. The log contains GNSS observations from the receiver without calculation of accurate coordinates.

IMG_0670

Downloading

After completing the survey, save logs to your Mac, Windows, Linux or mobile device.

  • Open the Logging tab
  • Turn off toggles to stop recording.
  • Find your logs below in the Logging tab.

You can see the recording date and time. There are two buttons on the right side of each log:

  • blue arrow button saves it.
  • red garbage can button deletes it.

Storing the base position

If you want to reuse the determined base location:

  • Carefully mark physical position on the ground
  • Save coordinates to manual using the button in the Base Coordinates section of the Base mode tab
  • When using this position next time, accurately place the base station over the mark
  • Enter the recorded coordinates manually in Emlid Flow

Official Documents available at Emlid's website.

Use the navigation menu below to continue the tutorial.

Previous

USB Drive Specifications

ROCK R2A Tutorial

Retrieve the R2A Data